Inglés
El portugués
EspañolCurrent
El malayo
Idioma indonesio
Alemán
El turco
El vietnamita
Francés
El ruso
El árabe
Tailandés
El japonés
Coreano
FFU y equipos de purificación de aire terminal
Unidad de filtro de ventilador de alta presión estática
A deep-plenum FFU for cleanroom duties with added air-path resistance, combining a backward-curved EC fan, reinforced casing and pressure-test access.
- Plenum de presión reforzada profunda
- Impulsor EC curvado hacia atrás
- Accessible Pressure-Test Port
- Variable-Speed Fan Adjustment
Introducción del producto
The high-static-pressure fan filter unit combines a backward-curved EC impeller, deep inlet arrangement and reinforced plenum. Formed ribs and corner reinforcement support the casing, while a capped test connection provides access for pressure measurements. The unit is intended for cleanroom selections in which inlet losses or final-filter resistance are important parts of the airflow duty. Pressure capability is evaluated at the required flow, not from the motor size or housing depth alone.
Características clave
Los nervios y las Esquinas reforzadas formadas limitan la desviación de la carcasa cuando el pleno funciona a una presión estática elevada.
Un puerto de presión tapado proporciona un punto de conexión repetible para las mediciones de puesta en marcha y mantenimiento.
Variable EC fan speed provides an adjustment range for balancing the selected fan and filter combination.
Soluciones para su aplicación
A high-resistance duty needs an airflow-and-pressure selection for the complete installation rather than a maximum-pressure figure in isolation.
An added duct collar changes the inlet condition assumed for an open-plenum selection.Include the actual duct and fitting losses when selecting the operating point.
Available airflow can fall as final-filter resistance increases.Check the loaded-filter duty against the fan curve and permitted operating range, rather than assuming the controller can always restore flow.
Higher internal pressure places additional demand on casing joints and filter seals.Pair the reinforced housing with the specified filter interface and inspect the assembled seals during commissioning.
A pressure reading alone cannot identify every cause of low airflow.Record inlet pressure, filter differential pressure and delivered airflow together to separate air-supply, filter and fan-setting issues.
Aplicaciones típicas
Sistemas de techo de sala blanca conectados a conductosFiltración terminal ULPARecirculation systems with added inlet resistanceHigh-resistance clean-air modulesProcess areas with variable air-path resistance
Parámetros técnicos
Common reference configuration choices for a pressure-duty ceiling FFU.
| Module-Format Option | Common nominal format: 2 x 4 ft |
|---|---|
| Fan and Drive | Backward-curved centrifugal impeller with variable-speed EC drive |
| Pressure-Plenum Construction | Deep reinforced casing around the fan and final-filter support |
| Velocidad superficial de referencia | Typical selection target: 0.45 m/s through the final-filter face |
| Air-Inlet Options | Open-plenum inlet or duct-collar connection |
| Pressure-Test Connection | Capped static-pressure tapping on the fan plenum |
| Opción eléctrica | Common supply option: 230 V AC |
| Control-Interface Options | Local speed setting, 0-10 V analogue reference or compatible network controller |
| Final-Filter Configuration | HEPA or ULPA panel selected with the fan duty |
| Perimeter-Seal Options | Dry-gasket compression or matched gel-seal construction |
| Customization | Disponible según la aplicación prevista y el entorno operativo. |
Opciones disponibles
Cuello de conducto o entrada superior abiertaSelección de motor e impulsor de alta presión ECFiltro de puerto de presión diferencialFiltro HEPA o ULPA de paquete profundo con interfaz de gel
Pressure-Duty Selection and Installation
Define the full resistance path
For a quotation, state the required airflow and external losses at that airflow, including inlet ductwork, fittings and any prefilter. List the final-filter resistance separately so that internal filter pressure drop is not counted twice. The selected fan curve must cover both the clean-filter duty and the intended loaded-filter limit.
Match the inlet and control arrangement
Choose an open intake or a dimensioned duct collar, the final-filter grade, and the gasket or gel-seal construction. An EC motor does not by itself establish constant-airflow operation. Where an upstream air-control device is used, select compatible control behaviour rather than allowing two independent controllers to regulate the same airflow.
Install for measurement and service
Allow access to the test connection, motor controls and filter removal path. Use the specified ceiling support layout and electrical rating, and measure delivered airflow as well as pressure during balancing. Disconnect power before filter or fan maintenance.
A standard fan filter unit may suit a lower-resistance ceiling duty. If the main requirement is increased total volume across a broad outlet, compare the high-airflow fan filter unit.
¿Planificación de una especificación de la Unidad de filtro de ventilador de alta presión estática?
Envíenos sus dimensiones, condiciones de instalación, objetivos de rendimiento y acabado superficial requerido.
