Bahasa Inggris
Bahasa Portugis
Bahasa Spanyol
Bahasa Melayu
Bahasa IndonesiaSaat ini
Bahasa Jerman
Bahasa Turki
Bahasa Vietnam
Bahasa Perancis: Bahasa Perancis
Bahasa Rusia
Bahasa Arab
Bahasa Thailand
Bahasa Jepang
Bahasa Korea
Filter udara dan filtrasi kimia
Karbon aktif Pocket Filter
A multi-pocket filter combining particulate media with a distributed activated-carbon layer to remove fine dust and light-duty gaseous contaminants in one HVAC stage.
- Particle and Gas Filtration
- Conical Pocket Geometry
- Distributed Carbon Layer
- Large Media Surface
Perkenalan produk
The activated carbon pocket filter combines an upstream particulate layer, a bonded activated-carbon layer and a stabilizing downstream support within multiple tapered pockets. The long pockets provide a much greater media area than a flat panel and distribute both particle loading and carbon adsorption over the airflow. Stitched or ultrasonically welded spacers keep the pockets separated, while a steel or molded-polymer header fits standard bag-filter housings. It is intended for indoor-air-quality duty where moderate odors and particulates must be addressed without installing two separate filter stages.
Fitur utama:
Tapered pockets remain separated at design flow and use the available housing depth efficiently.
The distributed carbon layer exposes adsorbent across a broad area instead of concentrating it near the header.
A rigid header provides a familiar replacement interface for standard front- or side-access bag-filter systems.
Solusi untuk aplikasi Anda
Separate particle and molecular stages consume valuable air-handler length, yet a thin carbon panel may not provide enough active area for the required airflow.
The air handler lacks space for a particle filter followed by a separate carbon cassette.Composite pocket media combines both functions within one standard bag-filter stage.
Flat carbon media has too little exposed area at the system airflow.Multiple deep pockets increase the available carbon-coated surface behind the same face opening.
Bag pockets touch and block one another at reduced airflow.Tapered geometry and internal spacing retain open channels through the filter bank.
Particulate loading covers the carbon before its adsorption capacity is used.A dedicated upstream particle layer protects the distributed carbon surface from coarse dust.
Aplikasi yang Tipis
Commercial building supply airHospital general ventilationAirport and transport facilitiesLaboratory support-area HVACCleanroom prefiltration with odor control
Parameter teknis
Representative construction ranges for a combination activated-carbon pocket filter are shown below.
| Bahan inti | Synthetic or glass-fibre particulate medium laminated with bonded activated-carbon media |
|---|---|
| Ketebalan Panel (Panel Thickness) | 360–640 mm pocket depth |
| Efektif lebar | 287–592 mm nominal header width |
| Panjang maksimum | Up to 640 mm pocket length |
| Baja menghadap ketebalan | 0.6–0.9 mm painted or galvanized-steel header frame when specified |
| Kepadatan inti (core density) | Approximately 80–160 kg/m³ equivalent composite-media density including bonded carbon |
| Konduktivitas Termal (Thermal Conductivity) | Approximately 0.040–0.080 W/(m·K) for the dry composite pocket medium |
| Permukaan selesai | Painted steel or molded polymer header with dark carbon-loaded pocket media |
| Jenis Bersama | Header-frame gasket or clamp-in pocket-filter connection |
| Customization (Kustomisasi) | Tersedia berdasarkan aplikasi yang dimaksudkan dan lingkungan operasi. |
Pilihan yang tersedia
Five to ten pocket configurationsSteel or incinerable polymer headerParticulate efficiency selected for the HVAC stageBroad-spectrum or impregnated carbon layer
Planning a Activated Carbon Pocket Filter specification?
Kirimkan kami dimensi Anda, kondisi instalasi, target kinerja dan permukaan akhir yang diperlukan.
