English
البرتغالية
الإسبانية
اللغة الملاوية
الإندونيسية
الألمانية
اللغة التركية
اللغة الفيتنامية
الفرنسية
الروسية
العربيةالحالي
التايلاندية
اليابانية
الكورية
اكسسوارات تركيب الغرف النظيفة
E مجمع إصلاح الايبوكسي
A two-component resin-and-hardener repair compound for rebuilding small damaged areas before sanding and hygienic surface finishing.
- Metered Two-Part Mixing
- Low-Shrink Hard Cure
- Sandable Repair Surface
- Multi-Substrate Bonding
مقدمة المنتج
Epoxy repair compound combines resin and hardener at a controlled ratio to form a dense thermoset repair material. Dual-cartridge packaging meters both components through a static mixer, reducing incomplete blending on small maintenance jobs. The mixed compound wets properly prepared metal, concrete and rigid panel surfaces, fills chips or localized voids and cures to a hard profile that can be shaped, sanded and overcoated with a compatible hygienic finish.
الخصائص الرئيسية
The static mixer produces a uniform blend without a separate mixing cup.
Low curing shrinkage helps the patch retain contact with sound repair edges.
The hardened surface can be machined or sanded before compatible topcoat application.
حلول للتطبيق الخاص بك
A localized cleanroom repair must bond to a carefully prepared substrate and finish flush without leaving a porous or dirt-catching patch.
Hand-proportioned resin and hardener can remain soft when the ratio is inaccurate.Matched dual cartridges meter both components before they enter the static mixing element.
Oil, dust or weak coating prevents a repair from anchoring to the base material.The defect is cut back to sound material, degreased and mechanically keyed before application.
A proud or rough patch creates a ledge that is difficult to clean.The cured compound is shaped and sanded flush, then closed with a compatible smooth finish.
Large deep fills can overheat or cure unevenly during the exothermic reaction.Repair depth and batch size are limited to the selected grade, with deeper voids rebuilt in controlled stages.
تطبيقات نموذجية
Cleanroom panel chip repairLocalized coated-metal defect fillingConcrete floor edge restorationEquipment base and curb repairsRigid frame and trim rebuilding
المعلمات الفنية
Typical construction and application ranges for a cartridge-dispensed two-component epoxy repair compound are listed below.
| المواد الأساسية | Two-component epoxy resin and amine hardener with mineral reinforcement |
|---|---|
| سمك اللوحة | 1-25 mm practical repair layer thickness |
| العرض الفعال | 5-100 mm typical localized repair width |
| الحد الأقصى الطول | Up to 1000 mm continuous localized repair strip per application |
| الصلب يواجه سمك | 0.50-2.00 mm compatible steel repair substrate thickness |
| الكثافة الأساسية | Approximately 1400-2000 kg/m³ mixed compound density |
| الموصلية الحرارية | Approximately 0.30-0.80 W/(m·K) for cured filled epoxy |
| إنهاء السطح | Dense sandable gray or off-white surface suitable for compatible overcoating |
| نوع المشترك | Bonded chip, crack, edge or shallow-void repair on sound prepared substrate |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Dual cartridge or hand-mix packFast or extended working timeGray or off-white compoundStatic mixer and application spatula kit
Planning a Epoxy Repair Compound specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
