Charcoal wrist strap tester with stainless touch plate three status lamps and cord jack

ESD 및 정전기 방지 제품

손목 스트랩 테스터

The Wrist Strap Tester checks the resistance path through a worn ESD wrist strap and cord, then displays a high, pass or low result for routine personnel grounding verification.

Three-state indication distinguishes high, acceptable and low resistance conditions.
Large stainless touch plate supports a direct operator test routine.
Compact sloped housing keeps the connection and result lamps easy to see.

견적 요청 제품 찾아보기

상품 소개

This compact tester combines a stainless contact plate, a dedicated wrist-cord jack and three vertically arranged result lamps on a sloped front panel. The molded charcoal enclosure can sit on a counter or be adapted for a fixed entry-point position. During a test, the operator connects the worn strap cord and touches the metal plate to complete the measurement path through the skin, band and cord. The separated high, pass and low indications help supervisors identify an open/high-resistance condition or an unexpectedly low-resistance path without interpreting a numerical display.

주요 기능

High, pass and low lamps provide an immediate qualitative result.

Brushed-stainless touch plate offers a durable operator contact surface.

Dedicated wrist-strap jack prevents confusion with footwear interfaces.

Sloped front panel improves visibility at counter height.

Compact molded enclosure supports portable or fixed-point use.

Side power connection keeps supply routing away from the touch surface.

응용 프로그램 솔루션

A wrist strap checker must be simple enough for repeated daily use while distinguishing both high-resistance failures and unsafe low-resistance paths.

An operator enters the protected area with an open cord or poor skin contact.The high-result channel identifies a resistance path above the selected acceptance window.

A missing or bypassed current-limiting resistor is overlooked.The low-result channel identifies an unexpectedly low measured path for follow-up inspection.

Personnel misread a complicated numerical display.Three separated lamps communicate high, pass and low outcomes directly.

Inconsistent hand pressure makes testing awkward.The large metal plate provides a generous, stable contact area for the fingertip or palm.

The tester is difficult to see or reach at an entry station.A sloped face and compact footprint suit counter-level or wall-adjacent installation.

일반적인 응용 프로그램

ESD-protected area entry checkpoints.Electronics production shift-start verification.PCB assembly and repair departments.Static-sensitive laboratories and inspection rooms.Supervisor spot checks of wrist strap assemblies.

기술 매개변수

The representative construction below describes a single-circuit touch tester. Pass limits, cord connector, power arrangement and mounting method should be selected to match the established ESD compliance-verification plan.

핵심 재료	Flame-retardant ABS enclosure with electronic resistance-comparison circuit and metal contacts
패널 두께	2.0–4.0 mm molded housing and front-panel thickness
유효 폭	95–160 mm enclosure width
최대 길이	Up to 220 mm overall enclosure depth
강철 면면 두께	1.0–1.5 mm brushed-stainless touch-plate thickness
코어 밀도	1030–1080 kg/m³ ABS resin density
열전도도 (Thermal Conductivity)	0.17–0.22 W/(m·K)
표면 마무리	Textured charcoal housing with black sloped panel, silver contact plate and red/green indicator lenses
접합 유형	Single wrist-cord jack and stainless touch plate connected to a three-state resistance comparator
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Fixed or selectable upper resistance limit.Battery, regulated DC or regional adapter input.Banana, snap or application-specific wrist-cord jack.Visual indication with optional audible signal.Bench-top or wall-mount arrangement.Test-result relay or access-control output where required.

Planning a Wrist Strap Tester specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.