English
البرتغالية
الإسبانية
اللغة الملاوية
الإندونيسية
الألمانية
اللغة التركية
اللغة الفيتنامية
الفرنسية
الروسية
العربيةالحالي
التايلاندية
اليابانية
الكورية
أنظمة التحكم في الغرف النظيفة والمراقبة البيئية
استشعار تسرب المياه
A supervised leak sensor that detects conductive liquid along a cable or zone probe near cleanroom utilities and reports an alarm before water spreads.
- Sensing Cable or Zone Probe
- Supervised Circuit Integrity
- Fast Local Alarm
- BMS Relay Output
مقدمة المنتج
The water leak detection sensor monitors the electrical condition of a floor cable, rope sensor or compact zone probe. Contact with conductive liquid changes the sensing circuit and activates the local controller, while supervision identifies cable breaks or disconnected probes separately. The sensing element can be routed around AHU drain pans, humidifiers, chilled-water lines and raised-floor utility paths. Relay or network output sends leak and trouble states to the BMS so response can begin before water reaches clean finishes or sensitive equipment.
الخصائص الرئيسية
Circuit supervision distinguishes a leak alarm from a broken or disconnected sensor.
Resettable sensing elements can return to service after cleaning and drying.
Separate relay or network states report leak, cable fault and controller health.
حلول للتطبيق الخاص بك
A useful leak system must cover the likely water path, remain serviceable and signal cable damage before an actual leak occurs.
A point probe detects water only after it reaches one small location.A sensing cable follows the full perimeter or lowest likely flow path.
A disconnected cable leaves the area unprotected without warning.Supervised end-of-line monitoring creates a distinct trouble alarm for circuit loss.
The sensor must be discarded after a minor clean-water leak.A resettable cable can be wiped, dried and returned to monitoring service.
Water spreads under equipment before staff find the source zone.Zoned circuits and clear controller labels narrow the response area quickly.
تطبيقات نموذجية
AHU and humidifier roomsمطاردات فائدة غرف الأبحاثRaised-floor process areasChilled-water and drain lines
المعلمات الفنية
Typical construction values for a cleanroom water leak sensor and zone controller are listed below.
| المواد الأساسية | Conductive polymer sensing cable with fluoropolymer braid and polycarbonate zone controller |
|---|---|
| سمك اللوحة | 35-70 mm controller depth |
| العرض الفعال | 90-160 mm controller width |
| الحد الأقصى الطول | Sensing cable zones up to 30000 mm |
| الصلب يواجه سمك | 0-1.0 mm; optional stainless mounting plate |
| الكثافة الأساسية | 1700-2200 kg/m³ for fluoropolymer sensing-cable materials |
| الموصلية الحرارية | 0.20-0.30 W/(m·K) for fluoropolymer cable insulation |
| إنهاء السطح | White controller with blue status labels and white-yellow braided sensing cable |
| نوع المشترك | Supervised quick-connect sensing cable with end terminator and removable alarm terminals |
| التخصيص | متوفر على أساس التطبيق المقصود وبيئة التشغيل. |
الخيارات المتاحة
Zone cable or point probeMultiple sensing zonesLeak and trouble relaysModbus or BACnet gateway
Planning a Water Leak Sensor specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
