English
البرتغالية
الإسبانية
اللغة الملاوية
الإندونيسية
الألمانية
اللغة التركية
اللغة الفيتنامية
الفرنسية
الروسية
العربيةالحالي
التايلاندية
اليابانية
الكورية
أنظمة الجدار والسقف للغرفة النظيفة
غرفة نظيفة قناة قاعدة الجدار
A galvanized-steel or aluminum floor track that locates modular cleanroom wall panels, transfers base loads and creates a level, sealable interface above the finished floor.
- Level Panel Support
- Direct Floor Anchorage
- Sealed Base Interface
- Demountable Wall Compatible
مقدمة المنتج
Cleanroom Wall Base Channel is the structural floor track beneath a modular wall run. The channel establishes panel alignment, restrains lateral movement at the base and distributes the wall load to the slab. Lightweight formed-steel versions provide a simple head-and-base track, while adjustable two-part aluminum systems can compensate for floor variation and create a flush recess for resilient or resin flooring. Mechanical anchors secure the lower section and hygienic sealant closes the floor and panel interfaces, leaving the visible room junction ready for coving or a recessed floor return.
الخصائص الرئيسية
Mechanical floor anchors transfer base restraint independently of sealant adhesion.
Adjustable aluminum variants compensate for uneven slabs before wall panels are installed.
Recessed configurations accept a flush vinyl or resin floor cove without an exposed ledge.
Demountable wall panels can be removed while the base alignment system remains in place.
حلول للتطبيق الخاص بك
The base channel must keep the wall level, accommodate the selected floor finish and remain sealed where the partition meets the slab.
An uneven slab causes cumulative panel misalignment higher in the wall.An adjustable base interface or controlled packing establishes a level bearing line before panels are set.
Sealant alone cannot safely restrain movement at the foot of a tall partition.Mechanical anchors secure the channel directly to the structural floor.
A projecting track creates a ledge beside sheet flooring.A recessed base detail receives the floor cove flush with the cleanroom wall face.
Cleaning liquid can enter through an unsealed floor-track joint.Continuous sealant beneath the track and along the panel interface closes both leakage paths.
تطبيقات نموذجية
Modular cleanroom wall foundationsPharmaceutical partition basesModular laboratory partition foundationsFood-production hygienic wallsSemiconductor cleanroom enclosures
المعلمات الفنية
Typical cleanroom wall base channel construction ranges are shown below.
| المواد الأساسية | 6063 aluminum extrusion or formed galvanized/stainless steel |
|---|---|
| سمك اللوحة | 0.5–2.5 mm channel wall thickness |
| العرض الفعال | 50, 75 or 100 mm panel seat width |
| الحد الأقصى الطول | 3000–6000 mm per section |
| الصلب يواجه سمك | 0.5–1.0 mm for formed steel channel; N/A for aluminum version |
| الكثافة الأساسية | N/A — formed channel has no insulation core |
| الموصلية الحرارية | N/A — structural floor track, not an insulating panel |
| إنهاء السطح | Galvanized, brushed stainless steel, anodized aluminum or powder-coated aluminum |
| نوع المشترك | Mechanically anchored floor track with sealed panel seat and flooring interface |
| التخصيص | متاح بناءً على التطبيق المقصود وبيئة التشغيل |
الخيارات المتاحة
Fixed formed channelAdjustable two-part aluminum baseRecess for 2 mm vinyl flooringStainless steel or color-matched finish
Planning a Cleanroom Wall Base Channel specification?
أرسل لنا الأبعاد الخاصة بك، شروط التثبيت، أهداف الأداء والتشطيب السطحي المطلوب.
