English
Португальский
Испанский язык
Японский
Индонезийский
Немецкий
Турецкий
Вьетнамский язык
Французский
Русский языкТекущий
Арабский язык
Тайский
Японский язык
Корейский
Воздушные фильтры и химическая фильтрация
Фильтры ULPA низкого сопротивления
An extended-area U15 mini-pleat filter engineered to reduce pressure loss in high-recirculation cleanrooms while maintaining uniform airflow across the terminal face.
- Extended Media Area
- Optimized U15 Resistance
- Uniform Pleat Channels
- High-Recirculation Duty
Введение продукции
The low-resistance ULPA filter balances U15-class filtration with the fan-energy demands of continuously recirculated semiconductor cleanrooms. A deeper mini-pleat pack provides increased effective area, and calibrated hot-melt separators keep each narrow air channel open at design flow. The pack is bonded into a rigid anodized-aluminium frame and protected by low-obstruction faceguards. Careful pleat density, pack depth and face velocity selection reduce resistance without thinning the filter structure or compromising clean terminal airflow.
Основные характеристики
Calibrated separator spacing prevents narrow pleat channels from pinching under operating pressure.
Low-obstruction protective grids shield the pack while preserving an open discharge area.
The rigid aluminium perimeter maintains a flat seal plane in large ceiling and FFU modules.
Решения для вашего приложения
Because recirculation fans operate continuously, even a modest unnecessary pressure loss across each ULPA terminal becomes a significant energy penalty.
U15 filters force FFU motors to operate near their upper speed range.Extended media area reduces local velocity and preserves more available fan pressure.
Aggressive pleat spacing creates blocked channels and inconsistent resistance.Controlled hot-melt bead geometry keeps a repeatable clear path between adjacent pleats.
A protective screen blocks too much of the discharge area.A thin open-grid faceguard protects the pack with limited obstruction.
Large ULPA panels bow and lose their perimeter seal.Reinforced aluminium extrusions and bonded corners maintain flatness across the terminal opening.
Типичные приложения
High-recirculation semiconductor cleanroomsEnergy-conscious wafer fabrication baysUltra-clean flat-panel display facilitiesPrecision metrology clean spacesLarge fan filter unit arrays
Технические параметры
Typical construction ranges for an extended-area low-resistance ULPA filter are listed below.
| Основной материал | Extended-area ultra-fine glass-microfibre or ePTFE ULPA media with optimized mini-pleat separators |
|---|---|
| Толщина панели | 90–150 mm overall aluminium-frame depth |
| эффективная ширина | 305-610 мм номинальная ширина грани |
| Максимальная длина | Номинальная длина лицевой стороны до 1220 мм |
| Толщина линий стали | 0.4–0.5 mm low-obstruction coated-steel or stainless faceguard |
| Плотность ядра | Approximately 28–45 kg/m³ equivalent extended-media-pack density |
| Теплопроводимость | Approximately 0.032–0.043 W/(m·K) for the dry ULPA media pack |
| Поверхностная отделка | Natural anodized aluminium with clean white or stainless open-grid faceguards |
| Объединенный тип | Continuous EPDM gasket, polyurethane gel trough or knife-edge perimeter |
| Customization | Доступно в зависимости от предполагаемого применения и операционной среды. |
Доступные варианты
U15 or U16 filtration classGlass-microfibre or ePTFE media90 mm or 150 mm extended-depth frameGasket, gel or knife-edge terminal seal
Planning a Low-Resistance ULPA Filter specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
