Bahasa Inggeris
Bahasa Portugis: Bahasa Portugis: Bahasa Portugis
Bahasa Sepanyol: Bahasa Sepanyol: Bahasa Sepanyol
Bahasa Melayu (Bahasa Melayu)Semasa
Bahasa Indonesia: Bahasa Indonesia
Bahasa Jerman
Bahasa Turki: Bahasa Turki
Bahasa Vietnam (Bahasa Melayu)
Bahasa Perancis
Bahasa Rusia
Bahasa Arab (Bahasa Melayu)
Bahasa Melayu (Bahasa Melayu)
Bahasa Jepun
Bahasa Korea (Bahasa Melayu)
Aksesori Pemasangan Bilik Bersih
Hanger saluran
An adjustable galvanized trapeze hanger with two threaded rods and a slotted channel crossbar for suspending rectangular cleanroom ductwork.
- Twin Threaded Rods
- Slotted Channel Crossbar
- Independent Level Adjustment
- Galvanized Steel Hardware
Pengenalan Produk
The duct hanger forms a rigid trapeze below the structural attachment points. Two continuously threaded rods pass through the ends of a galvanized slotted C-channel and are retained by paired nuts and washers, allowing installers to set crossbar elevation and level before the duct is seated. The open channel accepts compatible saddles or restraint hardware without requiring holes to be drilled through the supported duct casing.
Ciri-ciri Utama
A slotted C-channel permits flexible positioning of compatible duct restraint hardware.
Broad washer stacks distribute clamping load at the rod-to-channel interfaces.
Zinc-plated steel offers a practical finish for dry indoor service plenums.
Penyelesaian untuk permohonan anda
Rectangular duct runs require a level, distributed support that can be adjusted around uneven overhead structure without puncturing the duct casing.
Fixed-length hangers make it difficult to level ductwork below an uneven soffit.Independent nuts on the two threaded rods allow each end of the channel to be adjusted separately.
Narrow point supports can distort light-gauge rectangular duct walls.The channel crossbar provides a continuous bearing line beneath the duct or its support saddle.
Drilling the duct casing creates avoidable leakage and contamination traps.The trapeze supports the duct externally and accepts separate restraint hardware through its slots.
Bare carbon-steel hardware can develop surface corrosion in service voids.Galvanized or stainless hardware can be selected to suit the plenum exposure.
Permohonan yang biasa
Rectangular cleanroom supply duct suspensionReturn-air duct trapeze supportsExhaust duct support framesAir-handler connection supportService-plenum HVAC installations
Parameter teknikal
Typical construction ranges for an adjustable galvanized cleanroom duct trapeze hanger are listed below.
| Bahan Teras | Galvanized carbon-steel C-channel, threaded rods, nuts, washers and anchor plates |
|---|---|
| Ketebalan Panel | 0.60-2.00 mm compatible rectangular duct wall thickness |
| Lebar berkesan | 200-1500 mm adjustable duct support width |
| Panjang maksimum | Up to 2000 mm slotted channel crossbar length |
| Keluli Menghadapi Ketebalan | 1.50-3.00 mm nominal channel wall thickness |
| Ketumpatan teras | Kira-kira 7850 kg/m³ untuk komponen keluli karbon |
| Kekonduksian Terma | Kira-kira 45-60 W/(m · K) untuk keluli karbon |
| Kemasan permukaan | Silver electro-galvanized or hot-dip galvanized steel |
| Jenis Bersatu | Twin threaded-rod trapeze with nut-and-washer clamped slotted channel |
| Penyesuaian | Boleh didapati berdasarkan aplikasi yang dimaksudkan dan persekitaran operasi. |
Pilihan yang boleh didapati
M8, M10 or M12 threaded rodsElectro-galvanized, hot-dip galvanized or stainless steelCustom crossbar width and slot patternOptional elastomer isolation strip or duct saddle
Planning a Duct Hanger specification?
Hantarkan kepada kami dimensi anda, syarat pemasangan, sasaran prestasi dan kemasan permukaan yang diperlukan.
