Industrial desiccant rotor dehumidifier with blue modular service doors

클린룸 HVAC 및 공기 처리 장비

산업용 건조제 로터 탈습기

A dual-air-stream dehumidifier that continuously adsorbs water vapor on a slowly rotating desiccant wheel and releases it into a heated reactivation airstream.

Continuous Desiccant Rotation
Separated Process and Reactivation Air
Low-Temperature Moisture Removal
Modular Service Sections

견적 요청 제품 찾아보기

상품 소개

The industrial desiccant rotor dehumidifier divides a high-surface-area desiccant wheel between process and reactivation sectors. The process fan sends humid air through the dry portion of the rotor, while a separate heated airflow drives captured moisture out of the rotating media and discharges it outdoors. Sealed sector plates, filters and controlled rotor speed maintain a stable moisture balance even when the room temperature is too low for efficient refrigerant condensation.

주요 기능

A silica-gel or molecular-sieve composite wheel presents thousands of parallel channels with low airflow resistance.

Independent process and reactivation fans prevent the wet exhaust stream from re-entering the dry-air outlet.

Electric, steam or gas reactivation choices match available utilities and operating-cost priorities.

Separate access doors expose filters, rotor drive, seals and heater components without disturbing adjacent air-treatment sections.

응용 프로그램 솔루션

Refrigeration alone loses dehumidification capacity at low temperature and cannot economically reach many process humidity targets.

A cold production room remains humid even though the cooling coil operates continuously.Desiccant adsorption removes vapor without requiring the process air to cross a refrigerated dew-point surface.

Leakage between wet reactivation air and dry process air causes unstable outlet moisture.Adjustable sector seals and balanced fan pressures maintain physical separation across the rotating wheel.

An overloaded prefilter contaminates the rotor face and increases pressure drop.Dedicated process and reactivation filter stages are accessible from separate service doors for scheduled replacement.

A fixed reactivation heater consumes full energy during a reduced moisture load.Modulating heater output and variable rotor speed reduce regeneration input as the required dry-air condition changes.

일반적인 응용 프로그램

Pharmaceutical powder processing roomsMoisture-sensitive electronics assemblyCold storage and freezer anteroomsControlled raw-material warehousesDry-air supply for laboratory equipment

기술 매개변수

Typical modular construction ranges for an industrial rotary desiccant dehumidifier are provided below.

핵심 재료	Silica-gel or molecular-sieve composite honeycomb rotor inside a mineral-wool-insulated galvanized steel casing
패널 두께	30-50 mm double-skin insulated casing panel thickness
유효 폭	900-2600 mm nominal process-section width
최대 길이	Up to 5500 mm overall modular unit length
강철 면면 두께	0.8-1.2 mm galvanized or pre-painted steel inner and outer skins
코어 밀도	40-80 kg/m³ typical mineral-wool casing insulation density
열전도도 (Thermal Conductivity)	Approximately 0.036-0.045 W/(m·K) for the mineral-wool casing fill
표면 마무리	Blue powder-coated access panels with galvanized internal frame and corrosion-resistant rotor housing
접합 유형	Cam-lock or bolted modular casing with gasketed doors, flexible duct collars and sealed rotor-sector interfaces
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Electric, steam or gas-fired reactivation heaterPrecooling and aftercooling coil modulesMERV 8 through high-efficiency final filtrationVariable-speed process fan and dew-point control package

Planning a Industrial Desiccant Rotor Dehumidifier specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.