Charcoal electrostatic-conductive PVC flooring roll with copper grounding strip

클린룸 바닥 시스템

정전기 전도성 PVC 바닥재

A permanently conductive homogeneous PVC floor that transfers charge through the sheet, conductive adhesive and copper grounding network in ESD-controlled rooms.

5×10⁴–1×10⁶ Ω Resistance
Permanent Conductive Matrix
Copper-Strip Grounding
Impervious Welded Seams

견적 요청 제품 찾아보기

상품 소개

Electrostatic-conductive PVC flooring disperses conductive particles through a compact homogeneous sheet so charge has a continuous path from the walking surface to ground. The sheet is installed with an approved conductive adhesive and connected to copper strips or grounding points designed for the room. Welded joints retain a closed, cleanable surface without interrupting the electrical network. This low-resistance category is intended for areas where sensitive devices, powders or electronic processes require faster charge drainage than a general antistatic finish provides.

주요 기능

A conductive compound throughout the 2 mm sheet avoids dependence on a temporary surface polish for primary electrical performance.

Typical resistance to ground of 5×10⁴–1×10⁶ Ω provides controlled charge drainage for designated ESD areas.

Conductive adhesive and copper tape connect individual sheets to the building grounding system.

Hot-welded seams maintain an impervious surface around equipment and cleaning routes.

응용 프로그램 솔루션

A conductive floor must drain charge predictably across the complete installed system rather than only at the visible sheet surface.

A decorative antistatic coating does not provide the low resistance required by sensitive electronics.Conductive particles extend through the homogeneous PVC body to support a 5×10⁴–1×10⁶ Ω system range.

Isolated conductive sheets have no dependable route to the building earth.Copper strips and conductive adhesive link the floor field to designated grounding points.

Floor seams become liquid and contamination paths after repeated cleaning.Routed hot-welded joints close the sheet edges while preserving the conductive installation below.

Humidity changes cause inconsistent static-control performance in unsuitable products.The selected flooring uses a permanent conductive matrix rather than moisture-dependent surface treatment.

일반적인 응용 프로그램

Microelectronics cleanroomsSemiconductor assembly and test areasMedical electronics productionInstrument calibration laboratoriesESD-protected packaging rooms

기술 매개변수

Representative construction data for a homogeneous electrostatic-conductive PVC sheet system are provided below.

핵심 재료	Homogeneous PVC compound with uniformly distributed conductive carbon and mineral particles
패널 두께	2.0 mm total conductive sheet thickness
유효 폭	2000 mm standard sheet width
최대 길이	Up to 20000 mm standard roll length
강철 면면 두께	0 mm; the conductive vinyl sheet contains no steel facing
코어 밀도	Approximately 1750 kg/m³ based on a 3500 g/m² sheet at 2.0 mm thickness
열전도도 (Thermal Conductivity)	Approximately 0.25 W/(m·K) for compact conductive PVC
표면 마무리	Dense marbleized conductive surface suitable for approved ESD maintenance products
접합 유형	Hot-welded sheet seams over conductive adhesive with copper-strip grounding connections
사용자 정의	의도된 응용 프로그램 및 운영 환경에 따라 사용할 수 있습니다.

사용 가능한 옵션

Sheet or modular conductive tile formatCopper-strip grounding layoutColor-matched hot-welding rodCoved wall transition and conductive adhesive system

Planning a Electrostatic-Conductive PVC Flooring specification?

치수, 설치 조건, 성능 목표 및 필요한 표면 마감을 보내십시오.

우리 팀과 대화하십시오.