Three-quarter view of terminal ULPA filter with clean downstream faceguard

Воздушные фильтры и химическая фильтрация

Фильтр терминала ULPA

A cleanroom ceiling ULPA panel configured for direct final-air delivery from terminal housings or fan filter units into ultra-clean production zones.

Ceiling-Terminal Format
Uniform Downstream Face
Shallow Mini-Pleat Pack
Gasket or Gel Interface

Запрос котировки Просмотреть продукты

Введение продукции

The terminal ULPA filter forms the final filtration surface between a ceiling housing or fan filter unit and the cleanroom. Ultra-fine mini-pleat media is bonded into a shallow anodized-aluminium frame with a clean downstream protective grid. The frame can include a flat gasket land, a gel trough or an integral knife edge to match the terminal module. A smooth discharge face and balanced pack geometry help distribute low-turbulence air across process zones, work benches and mini-environments without adding a separate downstream duct section.

Основные характеристики

The shallow panel mounts directly at the cleanroom boundary and removes the need for a remote final-filter section.

A clean downstream grid protects the pleats and presents a uniform visible ceiling surface.

Balanced mini-pleat geometry supports even face velocity across the occupied terminal area.

Gasket, gel and knife-edge frame profiles match common ceiling housings and fan filter units.

Решения для вашего приложения

The last filtration stage must integrate cleanly with the ceiling, seal around the full perimeter and deliver uniform air directly into the controlled zone.

A remotely installed final filter allows duct leakage downstream of the filtration stage.Terminal mounting places the ULPA pack at the cleanroom boundary and shortens the clean side of the air path.

Uneven filter-face velocity disturbs sensitive work directly below the ceiling.Balanced pleat distribution and an open downstream grid promote a more uniform discharge pattern.

The filter frame does not match the ceiling housing's sealing method.Dry-gasket, gel-trough and knife-edge profiles cover the principal terminal interface types.

Exposed pleats are damaged during ceiling cleaning.A flush cleanable faceguard separates the media from routine wipe-down contact.

Типичные приложения

Полупроводниковые потолки для чистых помещенийFan filter unit arraysUltra-clean process benchesPharmaceutical critical zonesPrecision assembly mini-environments

Технические параметры

Representative construction ranges for ceiling-terminal ULPA panels are shown below.

Основной материал	Ultra-fine glass-microfibre or ePTFE ULPA media with mini-pleat separators
Толщина панели	69–150 mm overall terminal-filter depth
эффективная ширина	305-610 мм номинальная ширина грани
Максимальная длина	Номинальная длина лицевой стороны до 1220 мм
Толщина линий стали	0.4–0.6 mm powder-coated or stainless-steel downstream faceguard
Плотность ядра	Approximately 30–50 kg/m³ equivalent ULPA mini-pleat pack density
Теплопроводимость	Approximately 0.032–0.045 W/(m·K) for the dry ULPA media pack
Поверхностная отделка	Natural anodized aluminium with a clean white or stainless downstream grid
Объединенный тип	Flat EPDM gasket, polyurethane gel channel or integral knife-edge terminal connection
Customization	Доступно в зависимости от предполагаемого применения и операционной среды.

Доступные варианты

U15 or U16 mediaGlass-microfibre or ePTFE packDry gasket, gel trough or knife-edge frameWhite powder-coated or stainless downstream grid

Planning a Terminal ULPA Filter specification?

Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.

Поговорите с нашей командой