English
Португальский
Испанский язык
Японский
Индонезийский
Немецкий
Турецкий
Вьетнамский язык
Французский
Русский языкТекущий
Арабский язык
Тайский
Японский язык
Корейский
Стенные и потолочные системы для чистых комнат
Профиль внутреннего покрытия чистого помещения
A radiused two-part aluminum cove that replaces a sharp internal junction with a smooth, cleanable transition inside controlled rooms.
- Smooth 50 mm internal radius
- Two-part clip-on construction
- Cleanable powder-coated surface
- Suitable for wall, floor and ceiling junctions
Введение продукции
The Internal Cleanroom Coving Profile forms a continuous concave radius where two room surfaces meet. A concealed backing section is fixed first, then the finished cove face clips into position to cover fasteners and bridge the junction. The rounded geometry makes wiping easier than a tight square corner and can remain in place while compatible wall panels are removed from nearby bays.
Основные характеристики
A separate backing channel keeps primary fixings behind the finished face.
Clip-on assembly creates an even exposed line along long room junctions.
Powder-coated aluminum tolerates routine wipe-down cleaning.
Matching end caps and three-way pieces can finish intersecting cove runs.
Решения для вашего приложения
Sharp internal corners are awkward to wipe, visually emphasize sealant irregularities and can collect residue at the meeting point of two surfaces.
Cleaning cloths cannot maintain full contact inside a tight 90-degree recess.A 50 mm concave radius creates a broad, accessible wiping path.
Exposed fixings interrupt the surface at a hygiene-critical junction.The finished cove snaps over its backing channel and conceals the attachment points.
Hand-formed corner sealant often varies in width and appearance.A factory-extruded face establishes a uniform radius along the entire run.
Complex corner intersections require improvised cuts that are hard to seal neatly.Compatible end, internal and three-way accessories provide shaped termination pieces.
Типичные приложения
Wall-to-ceiling cleanroom junctionsWall-to-wall internal cornersWall-to-floor perimeter transitionsHygienic laboratory interiorsPharmaceutical processing rooms
Технические параметры
This profile is a finishing component rather than an insulated panel. Its defining dimension is the internal radius and its material properties come from the aluminum extrusion.
| Основной материал | Two-part 6063 aluminum backing channel and cove face |
|---|---|
| Толщина панели | N/A — not applicable to an internal coving profile |
| эффективная ширина | 50 mm standard internal cove radius |
| Максимальная длина | 3000 мм |
| Толщина линий стали | N/A — the profile is extruded aluminum |
| Плотность ядра | N/A-нет изолированного сердечника; плотность алюминиевого сплава составляет около 2700 кг/м³ |
| Теплопроводимость | N/A-нет изолированного сердечника; алюминиевый сплав составляет примерно 200 Вт/(м · К) |
| Поверхностная отделка | White polyester powder-coated or clear anodized |
| Объединенный тип | Snap-on cove face over a concealed backing channel with sealed edges |
| Customization | Доступно в зависимости от предполагаемого приложения и операционной среды |
Доступные варианты
50 mm radius internal coveAlternative 75 mm radiusThree-way internal corner pieceEnd caps and matching sealed transitions
Planning a Internal Cleanroom Coving Profile specification?
Отправьте нам ваши габариты, условия монтажа, целевые показатели производительности и требуемую отделку поверхности.
