Englisch
Portugiesisch
Spanisch
Malaiisch
indonesisch
DeutschCurrent
Türkischer Sprache
Vietnamesisch
Französisch
Russisch
Arabisch
Thailändisch
Japanisch
Koreanisch
Cleanroom Utility Systemen
Sauberes Dampfverteilungssystem
A prefabricated 316L distribution module that routes clean steam through a sloped main, top-fed branches and drained points of use.
- Sloped self-draining steam header
- Top-fed point-of-use branches
- Hygienic condensate removal
Produkteinführung
The Clean Steam Distribution System begins at the clean-steam source outlet and delivers steam to separated hygienic users without adding another generation stage. Its 316L main header is arranged with a continuous fall toward a drain pocket, while branch take-offs rise from the top of the main before descending to point-of-use valves. A clean-steam trap removes collected condensate at the terminal low point, and local pressure instruments provide operating visibility. Prefabricated supported sections reduce field joints while retaining the drainage, support and thermal-movement allowances required by the final route.
Key Features
Continuous header fall toward drainage
Three top-entry point-of-use take-offs
Drainable hygienic valve orientation
Orbital-welded primary tube joints
Terminal drain pocket and clean-steam trap
Local pressure indication and transmission
Prefabricated rack with defined pipe supports
Lösungen für Ihre Anwendung
A downstream clean-steam network must deliver dry, usable steam while continuously removing condensate and avoiding stagnant pockets across several intermittent users.
Condensate pools in a level header and can initiate water hammerInstall the main with a controlled fall toward a full-bore drain pocket and discharge through a correctly selected clean-steam trap.
Side or bottom take-offs carry wet steam into critical usersLift each branch from the top of the main before turning down to its point-of-use isolation valve.
Excess removable joints and dead legs complicate hygienic maintenanceUse orbital butt welds through the fixed runs and reserve hygienic clamps for components that require removal or inspection.
Thermal growth and changing demand strain pipework or starve remote usersSize each header and branch from the load profile, then coordinate guided supports and expansion allowance with the final route.
Typische Anwendungen
Autoclave and washer-sterilizer supplyBioreactor and process-vessel SIPAseptic filling-line steam barriersFood and beverage direct-steam servicesClean humidification distribution
Technische Parameter
Header diameter, branch size, steam pressure, drainage spacing, insulation, trap duty, support pitch and modular section length are selected from the connected load schedule and installed routing.
| Core Material | 316L stainless steel hygienic main header, branches, drain pocket and condensate discharge path |
|---|---|
| Panel Dicke | Sanitary tube wall typically 0.89–2.77 mm |
| Effektive Breite | Main and branch outside diameters typically 25.4–101.6 mm |
| Maximale Länge | Prefabricated supported module length typically up to 6000 mm |
| Stahl facing Dicke | Instrument and support plates typically 1.5–3.0 mm |
| Kerndichte | 316L Edelstahl dichte ca. 8000 kg/m³ |
| Thermische Leitfähigkeit | Edelstahl 316L ca. 15 W/(m · K) bei Umgebungs temperatur |
| Oberfläche Finish | Passivated 316L tubing with project-selected mechanically polished or electropolished internal finish |
| Gemeinsamer Typ | Orbital butt-welded fixed runs with hygienic clamp joints at removable valves, trap and instruments |
| Customisierung | Verfügbar je nach beabsichtigter Anwendung und Betriebsumgebung. |
Verfügbare Optionen
Header and branch diameter selectionPolished or electropolished internal finishInsulation with stainless protective claddingManual or actuated point-of-use valvesThermostatic or mechanical clean-steam trapSeparator and air-vent connection provisionsPressure and temperature monitoring pointsCondensate return or safe-discharge interface
Planning a Clean Steam Distribution System specification?
Senden Sie uns Ihre Abmessungen, Installationsbedingungen, Leistungsziele und gewünschte Oberflächenveredelung.
